Components
RAM Mounts®™ holds everything-everywhere and safe!
When the going gets tough and everything flies through the cockpit, RAM Mounts is your third hand. And your fourth! And fifth!
RAM Mounts is the adaptable mounting system for electronic devices and accessories. Whether it's a cell phone, clipboard, GPS tracker, mug, camera, radio: RAM Mounts provides a secure hold even in the most difficult terrain, or in the hectic workday in the warehouse.
Translated with DeepL
No results were found for the filter!
Magnetic base, 1.5 in. ![RM-330-Magnetbasis-15ß.jpg]( "RM-330-Magnetbasis-15ß.jpg")
This round magnetic base is a good foundation for your individual RAM Mount system. This circular base has a diameter of 6,35cm (2.5 "). Three strong magnets in a protective...
Magnet-Basis, 1 Zoll ![RM-311_Magnetbasis_100.jpg]( "RM-311_Magnetbasis_100.jpg")
Mit dieser runden Magnet-Basis wird eine gute Grundlage für Ihren individuellen Halter von RAM Mount geschaffen. Diese runde Basis hat einen Durchmesser von 6,35 cm (2,5"). Drei...
Magnetic adapter ![RM-814_Adapter.jpg]( "RM-814_Adapter.jpg")
This simple adapter fits your new or existing round base with 6.35 cm diameter. Note: Due to the limited retention force of the magnets we suggest to only use this mount with 1"...
Cheese plate set, 3,38 in. ![RM-233-Basis-Lochplatten-338.jpg]( "RM-233-Basis-Lochplatten-338.jpg")
A functioning RAM mount system always consists of a base, a connection and a device carrier. The choice of the right components creates a good basis for your individual holder....
Cheese plate set, 2,25 in. ![RM-232-Basis-Lochplatten-225.jpg]( "RM-232-Basis-Lochplatten-225.jpg")
A functioning RAM mount system always consists of a base, a connection and a device carrier. The choice of the right components creates a good basis for your individual holder....
Cheese plate set, 1,5 in. ![RM-133_Basis.jpg]( "RM-133_Basis.jpg")
A functioning RAM mount system always consists of a base, a connection and a device carrier. The choice of the right components creates a good basis for your individual holder....
Cheese plate ![RM-213.jpg]( "RM-213.jpg")
A RAM mount system always consists of a base, a compound and a device carrier. The choice of the right components marks a good start for your individual holder. This solution...
Bolt ball, 1/2 in. NPT ![RM-126_Kugelbolzen_NPT_150.jpg]( "RM-126_Kugelbolzen_NPT_150.jpg")
A bolt ball is the most simple kind of base for your RAM mount system. This bolt ball is a 1.5" ball attached to a female 1/2" NPT thread. Tip: This base can also be used as...
Bolt ball, 1,5 in. ![RM-107.jpg]( "RM-107.jpg")
A bolt ball is the most simple kind of base for your RAM mount system. This bolt ball is a 1.5" ball attached to a male M10x1.25 thread. Tip: This base can also be used as...
Bolt ball, 1 in. ![RM-103_Basis_100.png]( "RM-103_Basis_100.png")
A bolt ball is the most simple kind of base for your RAM mount system. This bolt ball is a 1" ball attached to a male M10x1.5 thread. Tip: This base can also be used as device...
Adhesive Base, 1 in. ![RM-316_Klebebasis_100.jpg]( "RM-316_Klebebasis_100.jpg")
Lightweight RAM mount systems can also be glued. This round base with 1" ball has a flexible rubber support surface so that uneven surfaces are also suitable for mounting.
Clamp base, 1 in. ![RM-227_Klammerbasis_100.jpg]( "RM-227_Klammerbasis_100.jpg")
This special basic clamp enables light RAM systems to be attached, for example, to a car side window edge lip or a glare shield on an airplanercraft.
Single screw base, 1 in. ![RM-135_Einzelschraubenbasis.png]( "RM-135_Einzelschraubenbasis.png")
This round base is a good foundation for your individual RAM Mount system. The base has a hole with a diameter of 11 mm. Tip: This base can also be used as a lightweight device...
Rectangular base, 2.25 inch ![RM-144-Basis-225.jpg]( "RM-144-Basis-225.jpg")
This universal mounting plate consists of a 2.25" diameter rubber ball, connected at right angles to a flat 15.9x5.1 cm (6.25x2 inches)rectangular plate. The plate contains...
Rectangular base, 1 in. ![RM-102_Basis_100.png]( "RM-102_Basis_100.png")
This rectangular base is a good foundation for your individual RAM Mount system. The base measures 2,54x5,08 cm (1"x2") and has two holes at a distance of 3.81 cm (1.5").